AEM 30-3300 WATER/METHANOL INJECTION KIT V2 PROGRESSIVE PUMP CONTROLLER WITH "BOOST SAFE" - INTERNAL MAP W/ 1 GALLON LOW PROFILE TANK. Increase power, reduce air inlet temps and suppress detonation at all boost levels. AXXIS OFF ROAD IS AN AEM AUTHORIZED DEALER. THE MOST COMPLETE KIT AVAILABLE ON THE MARKET.
UNIVERSAL KIT FOR TURBO OR SUPERCHARGED APPLICATIONS. BOOST DEPENDENT CONTROLLER WITH ON-BOARD MAP SENSOR. THE AEM WATER/METHANOL INJECTION SYSTEM ADVANTAGE. Water/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timingwithout using high-octane racing fuelfor power gains of up to 20%.AEMs Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system. Water/Methanol for up to 35 PSI on Forced Induction Gas Race Engines. This AEM kit is boost dependent for forced induction vehicles up to 35 PSI of boost (kit PN 30-3300). Note: FOR OPTIMUM RESULTS, ALL WATER/METHANOL INJECTION SYSTEMS AND GAUGES SHOULD BE RUN WITH AN AEM INLINE FILTER (AEM PART #30-3003). Robust, Easy to Use Controller Designs.
The new controller designs (Boost Dependent Kit PN 30-3300 & Multi Input Kit PN 30-3350) feature large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harnesses positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back. Both controller housings feature an easy to access integrated fuse and molded mounting tabs. AEMs Water/Methanol Injection kits wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation.Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. The controllers in AEMs Water Methanol systems include an integrated Boost Safe output feature that monitors the entire injection system and triggers a ground signal via an output if it detects a voltage-related error short, bad connection, broken wire, overheated pump, high or low voltage signal, etc. , allowing users to define their failsafe strategy from something as simple as flashing a warning light to more advanced strategies like pulling boost or ignition, or switching fuel maps on a standalone engine management system. Combined with the integral and highly accurate conductive low-fluid switch in the tank, Boost Safe can also put your engine in safe mode before the system runs dry. This exclusive feature is found only on AEM Water/Methanol Injection Systems. Heavy-Duty High Pressure Injection Pump. AEMs internally-bypassed water/methanol injection pump does not cycle on and off and provides quiet, smooth operation. Low-Profile 1.15 Gallon Tank. AEMs gas Water/Methanol Injection Systems are available with or without a compact 1.15 gallon tank that features an anti-starvation reservoir. A more accurate, conductive low level fluid sensor is integrated into the tank and features a positive lock connector with color-matched wires to the wiring harness. The sensor eliminates any chance of incorrect readings due to interference from debris.
Machined Billet Injectors and Nozzles. AEM includes one precision-machined billet injector in its gasoline Water/Methanol Injection kit. It features an integral check valve to prevent unintended fluid flow. Three billet injector nozzles are included for matching water/methanol flow to an engines horsepower output.
Boost Dependent and Multi-Input (0-5v/frequency) progressive controller designs feature large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs. Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, integrated pump ground circuit and additional wire for optional on/off fluid solenoid. Boost Safe failsafe output included (for complete failsafe under all conditions, see our Water/Methanol Failsafe Device).Heavy-duty high-pressure injection pump features integral fittings, a Santoprene diaphragm and EPDM seals to resist corrosion. Our pump maximizes line pressure for optimum atomization and its quiet, smooth operation is almost undetectable.
Precision-machined billet-aluminum injector with integral check valve. Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min).1.15 gallon tank with anti-starvation reservoir, integral conductive low-fluid sensor and positive lock connector (tankless systems available). 20 feet of injection tubing included. LED dash light for system status and low fluid warning. Reduces Air Inlet Charge Temps. The term liquid intercooling with water/methanol injection refers to a highly atomized mist of water/methanol that is injected into the airstream and begins to evaporate. As it does, this evaporative effect reduces air charge temps by as much as 100 degrees, and delivers a more oxygen-rich air charge. Water absorbs heat, and methanol is a cool burning, anti-knock rated fuel. When combined and introduced into the inlet stream, they can effectively increase your vehicles anti-knock index so you can reliably increase boost pressure and advance ignition timing using pump gas. Modern vehicles fitted with Exhaust Gas Recirculation (EGR) devices for emissions control promote heavy carbon build up inside the air intake. This carbon build-up can create hot spots in the combustion chambers that can cause detonation.
Water/methanol injection has a steam cleaning effect that reduces this carbon build up, and in some cases can increase fuel economy. THIS PRODUCT MAY BE USED SOLELY ON VEHICLES USED IN SANCTIONED COMPETITION WHICH MAY NEVER BE USED UPON A PUBLIC ROAD OR HIGHWAY, UNLESS PERMITTED BY SPECIFIC REGULATORY EXEMPTION. IT IS THE RESPONSIBILITY OF THE INSTALLER AND/OR USER OF THIS PRODUCT TO ENSURE THAT IT IS USED IN COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS.
THIS POLICY ONLY APPLIES TO INSTALLERS AND/OR USERS WHO ARE LOCATED IN THE UNITED STATES, HOWEVER CUSTOMERS WHO RESIDE IN OTHER COUNTRIES SHOULD ACT IN ACCORDANCE WITH THEIR LOCAL LAWS AND REGULATIONS. Important Safety Notice Regarding Methanol. AEM Water/Methanol Injection Systems are chemically compatible with a mixture of water and methanol, which we strongly recommend does not exceed a concentration of more than 50% methanol. Methanol is a toxic and highly flammable chemical.100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe.
The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol. Improper installation and/or adjustment of this product can result in major engine/vehicle damage.For technical assistance visit our dealer locator to find a professional installer/tuner near you. Note: AEM holds no responsibility for any engine damage or personal injury that results from the misuse of this product, including but not limited to injury or death caused by the mishandling of methanol. Thank You for Shopping with Axxis Off Road. Tracking numbers are updated manually, so please allow enough time for your information to be entered after your order has been placed.
We are not responsible for install mistakes. The RA # must be on the outside of each package with the RA # in a visible area. Any package without the RA # will be refused. This does not apply to defective items.
The item "AEM 30-3300 Water Methanol Injection Kit V2 MAP Sensor & BOOST CONTROLLER 35PSI" is in sale since Thursday, February 6, 2020. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Other".
The seller is "axxis-offroad" and is located in 40+ WAREHOUSES ACROSS THE US. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.