Each motor has a built-in MDR unit, saving space and setup time. A single motor can be powered directly from the cameras battery though a 7-Pin to P-TAP cable then daisy chained via 7-Pin to 7-Pin cable to run additional motors. There is no limit on the amount of motors an operator can attach per channel. The FIZ hand unit and two handle grips have a wireless range of 1000 feet. The signal from the FIZ hand unit can be upgraded to 1 1/4 miles with an additional accessory.
Both hand grips and FIZ hand unit run off (2) 18650 batteries. When fully charged the batteries in the hand grips can last up to 2 days. The batteries in the FIZ unit can last up to 10 hours. FIZ hand unit is capable of controlling 3 channels focus, zoom, and iris as well as overriding the hand grips. 0.8 mod, 35-tooth, 32 pitch gear with a face width of 10mm 13.
Motors can calibrate on lenses without hard stops such as photo-lens with follow focus gears. Motors fit standard 15mm and 19mm Rods 15.
Ideal for Gimbal, Drone, and Shoulder-mounted setups. (1) Wireless FIZ Hand Unit (2) Brushless Wireless Motors with 19mm Rod Support and 15mm Rod Bushings (1) Wireless Handle Left (Focus) (1) Wireless Handle Right (Iris, Zoom) (4) Follow Focus marking disks (1) 7-Pin to 740mm P-TAP Motor Power Cable (1) 296mm 7-Pin to 7-Pin Straight Motor Connection Cable (1) 180mm 7-Pin to 7-Pin Straight Motor Connection Cable (6) 18650 Battery (1) 18650 4 Slot Battery Charger (2) Handle to Arri Standard Rosette Adapter (2) Handle to Gimbal Bar Adapter (Compatible with 25mm/30mm Diameter) (1) Wireless FIZ Hand Unit Strap (1) Hard Shell Waterproof Safety Case. Material: Aluminum-Alloy Stainless Steel ABS Plastic Rubber Brazilian Rosewood. Weight: FIZ Hand Unit (with focus disk but no batteries): 0.972 lb FIZ Hand Unit (with focus disk and batteries): 1.164 lb.Right Handle Grip (no batteries or adapters): 0.582 lb Left Handle Grip (no batteries or adapters): 0.529 lb. Arri Rosette Male to Handle Grip Adapter: 0.161 lb 25mm/30mm Gimbal to Handle Grip Adapter: 0.099 lb. Motor (no rail adapter): 0.419 lb Motor with 15mm rail adapter: 0.496 lb Motor with 19mm rail adapter: 0.487 lb. Motor Dimensions: Length/Height: 4 1/2 Inches Width: 2 3/4 Inches (motor plus rail adapter) Width: 2 5/8 Inches (ports to tip of gear) Width: 3 2/8 Inches (end to end furthest points) Depth: 5/8 Inches (rail mount section) Depth: 3/4 Inch (base section) Depth: 1 3/8 Inches (motor section). After receiving the return, we will make a replacement depends on our available stock.
If you receive a not-as-described e. We may not accept your return without informing us in advance.We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem.
We care about our valued buyers, if you have any questions, our Customer Service staffs will be very glad to help you. We try our best to reply to your emails as soon as possible, however, due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. The item "TILTA WLC-T03 Nucleus-M Wireless Follow Focus Lens Control System DJI RONIN" is in sale since Wednesday, December 27, 2017. This item is in the category "Cameras & Photography\Film Photography\Movie Camera Accessories". The seller is "easyshopping08" and is located in Hounslow.
This item can be shipped worldwide.