LAUNCH X431 Elite Full System Full Functions for BMW, Auto VIN Scan, ECU Coding, Active Test, Guided Functions, 31+ Reset.. Instruments/ Self Leveling Suspension systems/.Seats/Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/. Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip Programming/Heated Rear Window/Xenon Headlights/Wash Wipe/Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors/Electronic Throttle/Navigation System/Rollover Sensor/Cruise Control/ Multi Function Steering Wheel/Aux Heating/Electronic Parking Brake/Clutch Electronics etc. 2.31+ Hot Maintenance Service! Reset the steering angle to zero to keep the car running straight. Write the new injector code into the car system for the correct cylinder injection quantity. Disable any lost keys and add new keys. ONLY for cars with an easy IMMO system. Especially works for D-P-F system with D-P-F regeneration, D-P-F component replacement teach-in and D-P-F teach-in after replacing the engine control unit. The vehicle air conditioner replaces the electronic control unit, replaces the actuator or the memory of the electronic control unit memory is lost, and requires air conditioning initialization learning.
Help exhaust the air after repair the ABS pump system. Reset urea after the diesel exhaust treatment fluid is replaced or filled up.
Initialize the throttle actuators to the default state. Makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors.Set the size parameters of the modified or replaced tire. Initialize the adaptive headlamp system. Initialize the sunroof when locked off or closed. Register the battery after replacement. Calibrate the memory in replaced or repaired seats. Allows you to perform reset for a new calculation of Engine Oil Life system once changed the oil. Set or learn Air/Fuel ratio parameters. Help complete the gearbox self-learning to improve gear shifting quality. Perform door window matching to recover ECU initial memory. Adjust the vehicle body height sensor for level calibration. Reset catalytic converter learned value stored in ECU. Set up the automatic start-stop function in ECU. Activate the electronic water pump. It is important in the maintenance of electronic braking system's safety and efficiency. The scan tool monitors certain camshaft position sensors signals to determine if all conditions are met to continue with the procedure for Engine running. Full OBD2 Check--Make a Better Detection for Car Engine System! Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs). Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors. Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data. I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs. O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer.
On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems. Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc. Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability. Other functions of the Launch x431 scanner.
(1)11 Kind of Language Supports English, French, Spanish, German, Italian, Russian, Portuguese, Japanese, Korean, Traditional Chinese, Polish. (2)Auto Vin Scan, Makes Diagnostic More Fast. (3)ECU Coding Match, learn, or code the newly replaced ECU; Customize your car, unfold the hidden features, or disable the annoying functions; Reprograms the adaptive data for certain components after repairs or replacements. ECU CODING allows you to match the ECUs with replaced components, flash hidden functions.
(4)Active Test (BI-Directional Controls) can actuate solenoids and actuators for active testing, send commands to systems/components to test their working status, without using the vehicle controls. It can read/erase codes, view live data, retrieve ECU info, do active test and service functions for all systems including ECM, TCM, ABS, SRS, BCM, BMS, TPMS, SAS, Fuel System, Light System and A/C system etc. (5)All in One LAUNCH BMW Diagnostic tools.
(6)Print and Share Diagnostic Report. LAUNCH Creader Elite Special Car Scanner. This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Diagnostic Equipment & Tools\Code Readers & Scanners". The seller is "kingbolen_uk" and is located in this country: GB. This item can be shipped to all countries in Europe.